February 1971 · Vol. 5 No. 4
February 1971 Magazine (Vol. 5 No. 4)
Magazine · 20 pages
Search this issue
February 1971 Magazine (Vol. 5 No. 4)
Captured text — scan page 14
Automatically captured text may contain recognition errors. Compare it with the original scan.
Al is a serious contender for the national wildwater canoeing
championship. He has fiberglassed at least a dozen canoe
paddles to aid his efforts, and has arrived at the following
method as being most satisfactory. — Editor
How to Fiberglass a Canoe Paddle
by Al Button
Fiberglassing a canoe paddle blade increases pieces of 4 oz. cloth similarly, except make
its life. A paddle thus processed is less likely to them 2 inches wide.
chip or crack, and the protection is a must in Mix a small amount of epoxy resin, about 1
serious whitewater paddling. inch in the bottom ofa paper cup. (I use epoxy
Materials required are: Paddle, sandpaper or _ because its finish is tougher and harder than
varnish remover, newspapers or plastic alternate products, and it is easier to work with
dropcloth, scraps of 4 oz. and 6 or 7 oz. _ because it’s gluey.)
fiberglass cloth, scissors, paper cup, small Lay a 4 oz. strip on waxed paper. Use brush
amount of epoxy resin, waxed paper, 1 to 2” to wet strip with resin. Stack.on second 4 oz.
brush, 1 to 3 pieces (bundles) of roving, rubber strip and wet down. Add the 6 or 7 oz. strips
or plastic glove, rag, acetone cleaner. one at a time, wetting each with resin. Stretch
Assemble your materials. Apply sandpaper each strip lengthwise as you lay it down (the
or varnish remover to the bottom 2 inches of pjas cutting permits maximum stretchability).
the paddle blade. Tape the paddle, blade Use a piece of roving 1 to 1-1/2 inches
upward, to a table leg or other similar structure. shorter than strips of fiberglass cloth. (Two or
Protect floor and table with newspapers or three bundles are recommended for heavy
plastic. Bias cut two pieces of the 6 or 7 0Z. paddle use.) Using rubber or plastic glove, dip
fabric 1-1/2 inches wide by 9 to 10 incheslong one end into the resin, then the other. Lay
(1 inch longer than paddle width — an 8-inch — soaked-out roving on top of cloth stack. Gently
blade requires a 9-inch length of fabric). Trim jigt stack by ends and flip over the end of the
corners or round ends of cloth. Bias cut two paddle lengthwise. Fan corner crease until it
INSIDE |NEXT To PADDLE TIP
2-3 ROVING STRANDS
YN QOOS
STRETCH OSS Mae reeieer ee CON 5
SOKO SORE yw OK)
SEPEROOKES ra a Y, y
aan a SAE oz. BIAS CUT ‘le X 9 fz Y Lees
LEO KASOR ORR OOO
sesesecaerenrtete VRE STRETCHED BRR RRR RR RRA BERK
OARY CORK RY ERD x ERY VRID Y
GRRAR OOS
SOLOERR
OSES Wh mS
RRR
TTI OIRESEESE
STRETCH 8% RRR RRR i SERRE ROORY oN STRETCH
y *, AR °,
RRR RIL VAY RK RRO
SH BRR ORR IO —>-
RRR RRR PRL RER
RRR RRL KKK LEE Mi DEER LORE
RRL RRA RRA ARAKI XA RR RD
STRETCH
STRETCH me 4-0z. 2" x lo" oS
OUTSIDE
12 HUT! — FEBRUARY 1971
Article contents & approved summaries (0)
No article summaries are available for this view.