April 1971 · Vol. 5 No. 5
April 1971 Magazine (Vol. 5 No. 5)
Magazine · 24 pages
Search this issue
April 1971 Magazine (Vol. 5 No. 5)
Captured text — scan page 23
Automatically captured text may contain recognition errors. Compare it with the original scan.
How to Make
and Attach a
Carrying Yoke
by Al Buchholz
A well-fitted carrying yoke can increase the
enjoyment of your canoe trips and, at the same
time, add support near the gunwales of your
canoe.
The carrying yoke can be made from oak,
ash, or mahogany; sitka spruce gives a strong,
light-weight yoke. Start with a 1 in. x 5 in. x 3
foot piece of wood. Before you cut into it, cut
a yoke from corrugated cardboard and shape
until. the neck hole and nibs fit you comfort-
ably. A design which works well for the guide
model canoe is given in the figure. Note that
the indentations of the yoke are offset for
greater strength. Add or subtract length at the
ends to fit your boat. After you have made a
cardboard yoke that fits you, trace it on the
wood and cut it out. Round the edges. Be sure
to taper the inside of the neck hole to fit your
shoulders if you don’t add pads. Cut the length
to fit your canoe (see where to place it below).
After sanding, cover with a good spar varnish or
exterior polyurethane.
Pads may be made from 2% in. x 5 in. x %
in. pieces of exterior plywood and 1-2 inches of
‘foam padding. Seal the plywood before cover-
ing. Use a firm type of foam such as that from
an old water skier’s belt. Cover the foam and
wood with nylon, Naugahyde, or plastic. The
last two may get hot on long portages. Canvas is
also good for covering but may not dry well.
Screw the pads onto the thwart from the
underside with brass screws. Offset the pads a
little. With pads, less care is required in fitting
the neck hole of the yoke.
Where to attach the yoke? This is a matter
of individual preference. I like mine about 2-3
inches forward of the center of balance of the
canoe (the carrying yoke has to go on last!).
This allows you to see when portaging as the
canoe will be slightly stern heavy. Other people
prefer to put the yoke dead center and push up
the front of the canoe when necessary. _
How to attach the yoke? Another matter of
preference. The strongest way is to shape a cut
piece to the edge of the canoe, rounding all
sharp corners. The piece is glued (epoxy is best)
to the inside of the canoe. Rough sand the edge
of the canoe for better adhesion. A scrap of 4
or 7% ounce fiberglass cloth is cut on the bias
(45° angle) and used to glass in the piece. In
the figure, this is shown as the dotted line. The
yoke is screwed into this as shown.
Another way is to screw a block through the
outside of the canoe. When doing this, add
waterproof glue to the hole to seal it. Yokes
may also be attached to the gunwales. Use brass
screws as they do not discolor.
For aluminum canoes, Grumman sells a
padded yoke on an aluminum tube which can
be added to canoes of the same width as
Grumman models. The pads are a little weak.
Be sure to check whether it will fit your canoe.
You will find that the time spent in making
a yoke will more than repay you on the portage
trail.
PAD PLACEMENT
CANOE EDGE
WOODEN SUPPORT
FIBERGLASS
GLASSED IN
SUPPORT
BLOCK SUPPORT
_[PLYwoooy |
Yoke PAD
Drawings by Larry Lapole
Article contents & approved summaries (0)
No article summaries are available for this view.