January 1985 · Vol. 21 No. 1
January 1985 Magazine (Vol. 21 No. 1)
Magazine · 32 pages
Search this issue
January 1985 Magazine (Vol. 21 No. 1)
Captured text — scan page 25
Automatically captured text may contain recognition errors. Compare it with the original scan.
Set up the appropriate form at any station, center it and clamp it in
place. Now, near each end of the 2x2, drill through it and the form. Drill
oversized holes, making a really sloppy fit for your bolts. Use large flat
washers and bolt the form in place. When all forms are installed and the end
pieces are in place, the assembly must be trued. Take your time and do this
right. It will affect the way the boat paddles.
_ Start the trueing with the end pieces. Make sure that they are in the
same plane. An easy way is to fasten a strip of wood to the same side of
each end piece long enough to extend a couple of feet above the form.
These two strips should be parallel (or one should eclipse the other) when
viewed from the end. Do whatever you need to be sure that they are. The
end pieces must also be trued to the center line of the strongback. Take
your time and do these steps carefully.
When satisfied, tack a small nail into each end piece in the edge near
the top of the form. Stretch a string between these nails and adjust it so it
just clears the highest form. This line should represent the keel line of your
boat. (Your forms should have a center line on them; it should be drawn
before you saw the forms.) Loosen the bolts on one form and adjust its
position so the center line matches the line on the strongback and the string.
When it does, tighten the bolts and move on to the next one. This is the
change I've made; it's better than shimming the forms.
When all the forms are trued, spend a little time checking fairness.
This operation works best with two people. Lay a strip anywhere on the
forms (lengthwise). Notice how the strip lays—does it touch all the forms
that it crosses or are there odd bumps? Go over the entire form every few
inches checking for bumps. Any bad bumps ean be cut down by resawing or
sanding away material. Take your time fairing your forms; the shape of your
boat depends on this hour well spent.
When everything is trued and faired up and all the bolts are snugged,
you should stand back and admire your handiwork. At this point you should
be able to visualize the boat you're building. Is it what you expected? Once
you start stripping it's too late to change much. Look at it right now, think
about how it will run, and enjoy. — Bob Brown
SANDING SEALER
Betty Ketter is the North MCA Resin Depot and the Minnesota dis-
tributor of Wenonah Canoes. She contacted Mike Cichanowski of Wenonah
and a representative of Northwest Fiberglass, which sells Ashland Chemicals
and supplies resin to the MCA. They both feel that since sanding sealer is a
paint and from a different family of chemicals than polyester resins, "Never,
never, never put resin over paint."
WAX AND RESIN
Polyester resin hardens (not dries) during an exothermic (heat emit-
ting) air-inhibited chemical reaction—the surface WILL NOT completely
cure unless the wax additive is mixed in that coat. No sanding or use of the
boat is reasonable unless that final surface is cured like all the molecules of
resin below.
The MCA purchases resin without the wax to prevent this final cure in
an effort to improve the bonding of intermittent coats. The Resin Depots do
have wax that can be added to your resin. However, this wax will not mix
well with the resin if the temperature is below 50 degrees Farenheit!
Improperly dissolved wax may cause spotty cures on the surface of your
canoe. — Betty Ketter HUT! 25
Article contents & approved summaries (0)
No article summaries are available for this view.