← Back to The HUT

February 1987 · Vol. 23 No. 2

February 1987 Magazine (Vol. 23 No. 2)

Issue first-page cover

Magazine · 40 pages

February 1987 Magazine (Vol. 23 No. 2)

Captured text — scan page 14

Automatically captured text may contain recognition errors. Compare it with the original scan.

This shows the complete scan page, including any other material on it.

BUILDERS CORNER-~-I LOVE LONG DECKS

Long decks are heavy and impractical. but I love to see them and
will continue to put them on my boats. My latest boat, the Tern, has
30" decks for and aft.

I've developed a system that helps to keep the weight managable.
My decks are labor intensive (they take time), but any klutz can put
them together.

These decks are attached after the inner gunnel is in place, but
before the outer rub rail is installed.

You must first decide how long they should be and how much crown
you wish to have. Having made these decisions, you can build a cross
member (deck beam) that will go from gunnel to gunnel at the inner
ends of each deck. The strip deck will be supported by this beam and
the edges of the hull.

Fair up the edges so the strips have a reasonably flat surface to
lay on and start stripping.

I lay up all strips on a dry run first. I let the ends over hang
the edges of the boat. I also bevel the bottom edges of tje strips
to assure a good fill on the outside.

When both ends are filled with strips, I label all parts and
disassemble the parts.

I next prime the bottoms and edges of all parts trying to keep
the outside free of resin. When this primer is cured, I lightly sand
all the primed surfaces.

I use West System Resin as a primer. I also use it as the glue
that holds this deck together. I coat the top edges of the hull and
recoat my strips as I reassemble all the parts. Be sure to use
enough staples to hold the strips flat and smooth.

Once this resin has cured, trim off the surplus and start
sanding. I sand the outer surface with 36 grit paper, then when it
is clean and smooth, I graduate to 50 or 60 grit. I round off all
edges and sand a couple inches down on the top of the hull. Now you
are ready to glass.

Only the outside of the decks is glassed. One layer of glass over
the top and an inch down the sides will do the job. When cured, sand
again with 50-60 grit and paint on a finish coat of epoxy.

Install the outer gunnels and any other trim, and enjoy.

--Bob Brown

Cedar Obrips: a

” °
x 7s SG r

50 board feet S06 s 88a

square edge $ 83 o BES
bead & cove $103 2 B gc

14 HUT!

Articles (10) · Summaries (10)

Generated issue overview: February 1987 issue of HUT!, the monthly publication of the Minnesota Canoe Association. The issue includes canoeing and canoe-building articles, editorials, letters, association business, chapter updates, event information, a member survey, advertisements, classifieds, and forms.

Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.

FROM THE BOW

Title transcribed from original publication

Generated summary: The MCA president encourages members to attend the Builders Show and annual banquet, then reflects on Dorothy Moulter’s death and the legacy of notable people associated with the Northwoods.

Open scan page 5

Read captured page 5 →

BEST "ALL AROUND CANOE" - A NEW COMERS PERSPECTIVE

Title transcribed from original publication

Generated summary: A newer paddler recounts trying several types of boats and explains why an Aquaterra Chinook sea kayak became his choice for versatile paddling, including rough water and longer trips.

Open scan page 10

Read captured pages 10–11 →

I'D RATHER BE CANOEING

Title transcribed from original publication

Generated summary: The HUT! editor describes the challenges of assembling an unusually full issue, including decisions about the survey, banquet insert, board photographs, and other material.

Open scan page 11

Read captured page 11 →

CRUISE NOTES

Title transcribed from original publication

Generated summary: Suggests possible MCA cruises for 1987, including wilderness, regional river, spring whitewater, and Lake Superior trips, and invites members to lead or join outings.

Open scan page 12

Read captured page 12 →

BUILDERS CORNER--I LOVE LONG DECKS

Title transcribed from original publication

Generated summary: Describes the author’s method for building long strip decks on a canoe, from planning and assembling the strips to sanding, fiberglassing, and finishing.

Open scan page 14

Read captured page 14 →

CLIFF'S CORNER--THE BUCK STARTS HERE

Title transcribed from original publication

Generated summary: Proposes a system for MCA cruises involving advance reservations, participant fees, leader compensation, and safety responsibilities, and explains the potential benefits of the plan.

Open scan page 26

Read captured pages 26–27 →

FROM THE THWART

Title transcribed from original publication

Generated summary: Argues for simplicity, cooperation, and respect among canoeists rather than judging others by equipment, technique, or paddling style; the author illustrates the point with a remembered encounter with a family canoeing in the Ontario wilderness.

Open scan page 27

Read captured pages 27–29 →

CANOEING DOWN UNDER

Title transcribed from original publication

Generated summary: A letter from New Zealand describes the writers’ travels and canoeing, kayaking, and rafting experiences in Fiji and New Zealand, with plans to continue to Australia.

Open scan page 29

Read captured page 29 →

SOME THOUGHTS WE WISH TO PASS ON TO THE MCA

Title transcribed from original publication

Generated summary: The writers praise HUT! for sharing canoeists’ experiences and information, discuss the value and cost of efficient canoes, and note that criticism of paddling ability can make a spouse feel intimidated.

Open scan page 29

Read captured pages 29–30 →

EATING CROW

Title transcribed from original publication

Generated summary: In a short personal account, the author recounts a winter paddle with Cliff and reconsiders his earlier skepticism about long, straight-shaft paddles and traditional canoeing techniques.

Open scan page 34

Read captured page 34 →