From the Bow
Title transcribed from original publication
Generated summary: The MCA president discusses the upcoming annual meeting and election, the fall color cruise and builders contest, and the return of monthly social meetings.
Open scan page 4October 1987 · Vol. 23 No. 10
Magazine · 32 pages
October 1987 Magazine (Vol. 23 No. 10)
Automatically captured text may contain recognition errors. Compare it with the original scan.
This shows the complete scan page, including any other material on it.
BUILDERS CORNER--SANDING AND MORE SANDING
Gene Jensen once told me that if one word best described canoe
building, it had to be Sanding.
It's a sure thing, no matter how neatly you strip, you're going
to spend some time sanding. You sand before you glass and again
after. You will have to sand your trim and between varnish coats.
Don't waste time with 100 or 120 grit sandpaper. You won't get a
decent job, no matter how long you work.
The surface of a freshly stripped canoe is a series of flat spots
and angles between the strips. You want to remove all these corners
and create a smooth curved surface. Some folks use a plane for this
job, others use a belt sander (the worst possible tool) and some of
us use a Surform.
A Surform and lots of elbow grease will get you the best surface.
This tool doesn't care which way the grain runs--it simply eats up
the high spots. I use it at a 30 to 45 degree angle to the strips
and go over the entire exterior.
Yes, it does make a lot of nasty gouges. No, don't worry about
them just yet. Remember, you're trying to hack down any ridges.
You know when you have Surformed enough because the entire
surface is full of those nasty gouges. I mean all over folks, don't
start sanding 'til it is.
When you start sanding, use an orbital sander with 36 grit. Yes,
I said 36 grit. This coarse paper will remove the gouges left by the
Surform and it will do it fast.
When all the marks are gone, it's time to switch to 60 grit.
This will remove the scratches left by the 36 grit. There is no
reason to go smoother than 60 prior to glassing.
After the hull is glassed on the outside, more sanding is
required. 60 or 80 grit seems to smooth up the glass job faster than
coarse paper.
Sand thoroughly between coats of resin, you will require less
coats if you do. Get the hull as smooth as you can with the 80 grit
before your last coat of resin.
My exterior finish will wait until the inside is done, sometimes
it waits until the boat is tested for a couple hundred miles.
My exteriors are a couple of coats of satin finish varnish with a
light hand sanding between coats. Some folks sand with finer and
finer paper and go for a luster, my boats are built to work well and
look reasonable, I'm a 100 grit finish man.
If anyone out there has found an easy way to prepare the inside,
please, Please step forward. Share your secret with us.
I start with a paint scraper, removing all the glue drips, then
some Surforming followed by a big disk sander (lazy way out). This
big disk will only get into the flat areas, so I use a 5" disk on my
drill with 36 grit paper to get into curves that the big sander won't
reach.
I end up in the stems with coarse paper wrapped around a 1 x 2
and lots of hand sanding. On my bubble sides and near the heel I use
an old hardened paint roller as a round sanding block.
After doing all I can with the disks, I start with my Ryobi palm
sander. This 1/6 sheet sander does the flats fine and will get into
some of the curves if I place a foam pad under the paper. Thank God
for Ryobies.
The trim will need sanding. Here is the time to get out the 120.
Sand it as smooth as you can before varnishing and between coats.
Yes, Gene, sanding is a big part of canoe building. When a cloud
of cedar sawdust starts rising in Apple Valley, the neighbors know
that Brown's boatworks is in operation.--Bob Brown
October 1987-HUT! 19
Generated issue overview: October 1987 issue of HUT!, the monthly publication of the Minnesota Canoe Association. The issue includes MCA columns and articles, a canoe product review, canoe-building advice, chapter news, event information, advertisements, classifieds, and membership material.
Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.
Title transcribed from original publication
Generated summary: The MCA president discusses the upcoming annual meeting and election, the fall color cruise and builders contest, and the return of monthly social meetings.
Open scan page 4Title transcribed from original publication
Generated summary: The editor comments on debate about cruise organization and safety, paid trip leaders, elitism, and how experienced canoeists can teach constructively.
Open scan page 4Title transcribed from original publication
Generated summary: Jacobson argues for river-trip safety procedures, including leader and sweep roles, group spacing, whistles, emergency equipment, and rescuing swimmers before equipment.
Open scan page 6Title transcribed from original publication
Generated summary: Mitchell responds to Jacobson's proposed cruise rules, describing MCA safety efforts and arguing for better judgment and training rather than rigid rules applied without regard to circumstances.
Open scan page 8Title transcribed from original publication
Generated summary: A letter and appeal seek river-crew volunteers for Billy Curmano's planned 1988 Mississippi River swim performance, describing its environmental themes and the need for crew members from May through August.
Open scan page 10Title transcribed from original publication
Generated summary: Murphy reviews an Ally Pack collapsible canoe after a 580-mile trip on the Elk and Thelon Rivers, describing its performance, durability, modifications, and suitability for wilderness and whitewater use.
Open scan page 11Title transcribed from original publication
Generated summary: The board explains that monthly social get-togethers are being introduced in response to member survey requests and invites members to the first gathering on November 17.
Open scan page 15Title transcribed from original publication
Generated summary: Brown describes tools and sanding sequences for preparing a woodstrip canoe hull, including shaping with a Surform, using progressively finer abrasives, and sanding the interior and trim.
Open scan page 23Title transcribed from original publication
Generated summary: Brown argues that the MCA should help members improve their canoeing and camping skills, and describes how members can learn from others without treating advice as an insult.
Open scan page 26Title transcribed from original publication
Generated summary: Simpson recounts an MCA group's summer journey above 70 degrees latitude and mentions preparations for MCA participation in the Dragonboat Races in China, including a training weekend.
Open scan page 27Title transcribed from original publication
Generated summary: Loerch adds information about canoeing and camping around Reno's Bottoms, recommending maps for pools 8, 9, and 10 and noting the area's fall scenery and wildlife.
Open scan page 28