← Back to The HUT

September 1987 · Vol. 23 No. 9

September 1987 Magazine (Vol. 23 No. 9)

Issue first-page cover

Magazine · 36 pages

September 1987 Magazine (Vol. 23 No. 9)

Captured text — scan page 26

Automatically captured text may contain recognition errors. Compare it with the original scan.

This shows the complete scan page, including any other material on it.

BUILDERS" CORNER--POLY VERSES EPOXY PART II

In my last article, I compared the costs of poly and epoxy
resins. This month I'd Jlike to discuss the differences in
application,

Both types of resin have some things in their favor. Poly is
easier to use, but the epoxy (West System) is less damaging to your
health.

West System resin is easy to mix. We sell pumps that meter out
the resin and hardener in a five-to-one mix. One stroke on each pump
and you have a batch ready to mix. Ten strokes of each and you have
a very, very large batch. Simple, right?

Poly resins come in waxed and non-waxed types, you must
understand the differences. No wax is required in the epoxy systems,
making this simpler.

I still say that the poly is easier to use (if you know what
you're doing), because it flows into the fabric so much easier. The
poly resin can be applied with any short-napped paint roller, as it
will soak into your cloth or wood almost instantly. I can glass the
outside of one of my solo canoes, by myself, including all bias
strips in about an hour. Using epoxy, I'd only have a good start.

The end result of an epoxy job is a superior product, but you
must work to get it. The epoxy is more viscous, it soaks into the
fabric also, but at its own sweet time. Try to force the epoxy into
the fabric faster, and you are likely to get air entrainment. This
is a foaming that takes place if you over-work the resin. It shows
up as white streaks, or blotches.

This hard-headed Dutchman had a hard time learning to use epoxy.
The trick is to give it plenty of time to soak in. Spread the epoxy
onto the surface, working it as little as possible. You will
probably have some surplus resin on your first pass, LEAVE IT ALONE!
Allow the epoxy time to soak in completely, then squeeze off the
excess.

With either resin, I recommend priming the bare hull before
glassing. With epoxy, your best primer is epoxy. Press it into the
pores of the wood with a squeegee and you have the surface sealed.

When priming for a polyester job, I recommend two coats of poly
sanding sealer. One more thing to buy.

I don't consider any of these resins "safe," no matter what the
manufacturers claim. They are all hazardous to your health. The
poly is loaded with volatile parts that escape into the air during
application and cure. These fumes can kill you if you breath enough
of them. I always wear a mask when working with the polyester.

West System Epoxy, by contrast, gives off almost no smell. What
you spread on your hull stays there and hardens. I feel that it is
much safer.

Pot life and cure time are controllable in either system, but by
quite different methods. With West System, you have two choices of
hardener, fast or slow. This is your only control. At my depot, I
usually send customers home in the summer with slow cure, I save the
fast cure for winter time customers who will be glassing in a cold
shop.

With poly resin, you can regulate cure time nicely by adjusting
the amount of hardener that you add. With a little practice, you can
operate over a considerable temperature spread.

I often use two different cure speeds on the same job. I will do
all the lay-up with a non-waxed under-catalyzed batch of resin. This
gives me more working time to do all the laminating. After the
laminating is complete, and all bias strips and reinforcings are on,
I mix a batch of waxed resin and add a lot of hardener, I make this
batch very “hot." I paint this on the outside and the extra hardener
helps to cook-off the material below.

26 HUT!-September 1987

Articles (15) · Summaries (15)

Generated issue overview: September 1987 issue of HUT!, the monthly publication of the Minnesota Canoe Association (Volume 23, Number 9). The issue contains canoe-trip reports, safety and canoeing features, association updates, event information, advertisements, and classified material.

Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.

From the Bow

Title transcribed from original publication

Generated summary: A brief humorous editorial explains that the president's monthly message was missing because of computer trouble.

Open scan page 4

Read captured page 4 →

Unisys Club's “Univac Memory Float” Namekagon Trip Report

Title transcribed from original publication

Generated summary: A first-person account of a relaxed two-day Namekagon River outing, describing the paddling, swimming, campsite, playful activities, and friendships made on the trip.

Open scan page 4

Read captured page 4 →

National Park or Land Fill?

Title transcribed from original publication

Generated summary: The author describes finding scattered garbage and heavy motorboat use during a visit to Voyageurs National Park, while also noting its wildlife and potential as a canoeing destination.

Open scan page 7

Read captured page 7 →

Update on Thunder Road—Stuck on a Windswept Superior Shore....

Title transcribed from original publication

Generated summary: A letter updates the progress of a canoe journey across the St. Croix and Brule rivers to Lake Superior, recounting low-water travel, portages, rapids, and a wind-bound stay near Ontonagon.

Open scan page 10

Read captured pages 10–11 →

Deeper into God's Country—Paddle Iowa

Title transcribed from original publication

Generated summary: Bob Brown recounts paddling a hundred-mile stretch of the Mississippi in Iowa and joining the MADRAC group paddle, describing the welcoming towns, fellow participants, and memorable stops.

Open scan page 12

Read captured pages 12–13 →

Safety and Education—Lightning Storms

Title transcribed from original publication

Generated summary: An educational article explains lightning hazards and recommends safety practices for paddlers, including leaving the river, spacing out, crouching with minimal ground contact, and checking on others.

Open scan page 14

Read captured page 14 →

A Gesture

Title transcribed from original publication

Generated summary: An essay describes how a powerboat's attempt to be considerate by slowing down can create a hazardous wake for canoeists, and argues for better communication and an MCA policy on the issue.

Open scan page 16

Read captured page 16 →

I'd Rather Be Canoeing

Title transcribed from original publication

Generated summary: The editor reports on HUT! archive donations and bound volumes, notes that the president is not seeking reelection, and encourages members to consider serving on the MCA board.

Open scan page 17

Read captured page 17 →

Duluth Traveler

Title transcribed from original publication

Generated summary: A Twin Ports Chapter newsletter update recalls a moonlight paddle, mentions a delayed wilderness trip and an upcoming club election, and directs readers to contact a chapter leader about an Apostle Islands trip.

Open scan page 20

Read captured page 20 →

New Fire Policies to Be Implemented on Superior National Forest

Title transcribed from original publication

Generated summary: A report describes new Forest Service procedures that may allow some lightning-caused fires to burn under monitored conditions in the Boundary Waters Canoe Area Wilderness, while retaining strict protection for public safety and high-value areas.

Open scan page 24

Read captured page 24 →

Trip Report—Canoe-a-Brunch

Title transcribed from original publication

Generated summary: The author recounts a group paddle through the St. Anthony Falls locks, a brunch at St. Anthony Main, and a return trip to the river, inviting readers to a future outing.

Open scan page 25

Read captured page 25 →

Builders' Corner—Poly Verses Epoxy Part II

Title transcribed from original publication

Generated summary: The second part of a canoe-building comparison discusses the application, curing, safety, and shelf life of polyester and epoxy resins, concluding that epoxy produces a better finished product while polyester can be easier and more flexible to apply.

Open scan page 26

Read captured pages 26–27 →

Cliff's Corner—Magazine Field Tests—Bah Humbug!

Title transcribed from original publication

Generated summary: Cliff Jacobson critiques magazine gear evaluations, arguing that short testing periods, advertising pressures, and simplified ratings can mislead readers; he urges consumers to assess equipment through personal use and experienced advice.

Open scan page 28

Read captured pages 28–29 →

My Ride with Death on the Brule (or So It Seemed)

Title transcribed from original publication

Generated summary: Sheila Huber describes an alarming first kayaking trip on the Brule River, including repeated capsizes and fear, and concludes by recommending that beginners take instruction from trained professionals.

Open scan page 30

Read captured pages 30–31 →

A Postscript to “Death Ride”

Title transcribed from original publication

Generated summary: A brief editorial note clarifies that the group in Sheila Huber's account was not affiliated with the MCA or Rapids Riders Chapter and warns about outfitters renting equipment to unqualified customers.

Open scan page 31

Read captured page 31 →