← Back to The HUT

September 1987 · Vol. 23 No. 9

September 1987 Magazine (Vol. 23 No. 9)

Issue first-page cover

Magazine · 36 pages

September 1987 Magazine (Vol. 23 No. 9)

Captured text — scan page 26

Automatically captured text may contain recognition errors. Compare it with the original scan.

BUILDERS" CORNER--POLY VERSES EPOXY PART II

In my last article, I compared the costs of poly and epoxy
resins. This month I'd Jlike to discuss the differences in
application,

Both types of resin have some things in their favor. Poly is
easier to use, but the epoxy (West System) is less damaging to your
health.

West System resin is easy to mix. We sell pumps that meter out
the resin and hardener in a five-to-one mix. One stroke on each pump
and you have a batch ready to mix. Ten strokes of each and you have
a very, very large batch. Simple, right?

Poly resins come in waxed and non-waxed types, you must
understand the differences. No wax is required in the epoxy systems,
making this simpler.

I still say that the poly is easier to use (if you know what
you're doing), because it flows into the fabric so much easier. The
poly resin can be applied with any short-napped paint roller, as it
will soak into your cloth or wood almost instantly. I can glass the
outside of one of my solo canoes, by myself, including all bias
strips in about an hour. Using epoxy, I'd only have a good start.

The end result of an epoxy job is a superior product, but you
must work to get it. The epoxy is more viscous, it soaks into the
fabric also, but at its own sweet time. Try to force the epoxy into
the fabric faster, and you are likely to get air entrainment. This
is a foaming that takes place if you over-work the resin. It shows
up as white streaks, or blotches.

This hard-headed Dutchman had a hard time learning to use epoxy.
The trick is to give it plenty of time to soak in. Spread the epoxy
onto the surface, working it as little as possible. You will
probably have some surplus resin on your first pass, LEAVE IT ALONE!
Allow the epoxy time to soak in completely, then squeeze off the
excess.

With either resin, I recommend priming the bare hull before
glassing. With epoxy, your best primer is epoxy. Press it into the
pores of the wood with a squeegee and you have the surface sealed.

When priming for a polyester job, I recommend two coats of poly
sanding sealer. One more thing to buy.

I don't consider any of these resins "safe," no matter what the
manufacturers claim. They are all hazardous to your health. The
poly is loaded with volatile parts that escape into the air during
application and cure. These fumes can kill you if you breath enough
of them. I always wear a mask when working with the polyester.

West System Epoxy, by contrast, gives off almost no smell. What
you spread on your hull stays there and hardens. I feel that it is
much safer.

Pot life and cure time are controllable in either system, but by
quite different methods. With West System, you have two choices of
hardener, fast or slow. This is your only control. At my depot, I
usually send customers home in the summer with slow cure, I save the
fast cure for winter time customers who will be glassing in a cold
shop.

With poly resin, you can regulate cure time nicely by adjusting
the amount of hardener that you add. With a little practice, you can
operate over a considerable temperature spread.

I often use two different cure speeds on the same job. I will do
all the lay-up with a non-waxed under-catalyzed batch of resin. This
gives me more working time to do all the laminating. After the
laminating is complete, and all bias strips and reinforcings are on,
I mix a batch of waxed resin and add a lot of hardener, I make this
batch very “hot." I paint this on the outside and the extra hardener
helps to cook-off the material below.

26 HUT!-September 1987

Article contents & approved summaries (0)

No article summaries are available for this view.