← Back to The HUT

May 1973 · Volume/issue not printed or unknown

May 1973 Magazine

Issue first-page cover

Magazine · 24 pages

May 1973 Magazine

Captured text — scan page 17

Automatically captured text may contain recognition errors. Compare it with the original scan.

10.

iil

12.

13;

e Limits the amount of water that
can enter

e Provides additional structural
bracing.

For minimum flotation, fixed end

tanks made of fiberglass or rigid

foam will suffice. For moderate

flotation, add to the end tanks 2-

inch thick Ethafoam bulkheads.

Maximum flotation can be provided

with bow, stern and mid ships air

bags.

For foam materials, look under

“Plastics, foam’’ in the Yellow Pages.

For inflatables, childrens’ beach toys

have been used. There are also com-

mercial sources for pre-formed air
bags.

Here are some of the more popular

materials used in boat lay-up:

e Fiberglass cloth — usually 7% or
10 oz. material. This is a machine
woven cloth.

e Fiberglass roving — usually 18 oz.
material. The fibers are not
crimped during weaving. There is
a faction that believes roving pos-
sesses superior strength. Another
group believes that “all cloth”
is the only way to go.

© Polypropylene cloth — usually
4 oz. It is more flexible than fi-
berglass, has about half the den-
sity, and seems to resist fractures
better. It is also more expensive
than fiber glass.

e Fiberglass mat — usually 10.0z.
material. Mat soaks up resin like
mad and doesn’t add much
strength to the boat, but it is nor-
mally used to add bulk and stiff-
ness, such as along the gunwale
of an open canoe where holes will
be drilled to support some wood

work. It is also useful for securing

bulkheads or other bracing.
© Microspheres — (glass beads) —
can be mixed with the resin to
reduce weight by effectively de-
creasing the density of the resin.
The use of bubbles (glass beads)
_also tends to stiffen the laminate
(the boat).
e Bracing materials — since a C-2
eet have an outside keel, a
eel-like strip called a keelson is
often used on the inside of the
hull to stiffen it. Additional hull
bracing can take the form of
pieces of rope or foam imbedded
in the lay-up.
Although the seat ring itself will pro-
vide some strength to the deck, it
will be necessary to add lateral
braces (like ribs) behind the seats.
Compressible bulkheads can provide
some of the required bracing.
Bulkheads should not be made from
rigid material since this sets up high
stress areas adjacent to the joint.
Etha-foam makes a good bulkhead

14.

15.

16.

17.

material. It can be easily carved to
shape, then held in place with mul-
tiple layers of fiberglass cloth or
mat soaked in resin. Two bulkheads,
installed at 1/3 and 2/3 the length
of the boat, seem adequate. Be sure
to leave room for legs and feet in
front of both bulkheads. Some peo-
ple prefer not to install bulkheads at
all, depending instead upon rib-type
bracing for support. Boats without
center holes should use a maximum
of one bulkhead. Two bulkheads, in
this case, would cut cargo space to
zero.

Seat rings may be formed up dur-
ing construction or they may be
made from separate molds to be
installed later in the process. These
separate molds may contain seats.
There are, however, other types of
seats. The canvas sling seat is simply
a semi-circle of 12.5 or 14 oz. can-
vas whose curved edge is epoxied to
the underside of the seat ring. Hem
the leading edge by folding it over
twice and glueing it with contact
cement. Many people prefer the
wooden plank seat which is a 1 by
3-inch piece of wood set low in the
boat and attached to the sides of
the hull. Make sure that you can get
your feet under such a seat before
installing one in your own boat.
Knee pads should be resilient and
properly placed to be any good at
all. Some form of straps are neces-
sary to hold the knees onto the pads
and consequently the canoeist into
the boat. For all-out competition,
it is a must that these knee anchor-
ing devices fit correctly.

If your canoeing will be limited to
occasional rapids of no great conse-
quence, toe braces probably aren’t
necessary. If, on the other hand,
you really lean out there on a brace,
or you are considering learning the
eskimo roll, toe braces will be man-
datory. They provide a leverage
point for shoving your knees tightly
into their straps when using body
english to control the boat. Toe
braces should be positioned so that
you have to cram your legs in place
between the knee anchors and the
braces.

Although the toe braces are normal-
ly molded into the bottom of the
boat, you may make them adjust-
able by first placing them farther
astern than necessary. Add blocks
to bring the support point forward
to fit various paddlers, yourself in-
cluded. Another system involves two

- lengthwise brackets molded into the

bottom of the boat with sets of holes
drilled. every. couple of inches. A
piece of: aluminum tubing is used
for the toe brace. It can be moved
fore or aft to accommodate various

leg lengths.

18. The most common carrying handle
is simply a 12 to 20-inch piece of
rope poked through the boat a few
inches from the end, then knotted
to form a loop. To add strength to
the hole ‘and to seal the boat against
leaks (particularly when the ends
are used for flotation tanks) a hol-
low phenolic tube may be epoxied
into the hole, then trimmed to
match the contour of the boat.

19. Hole covers are handy to have when
it starts to rain and your canoe is on
top of your car. A boat full of water »
may weigh three quarters of a ton!
They also cover up the indelible mud
that you don’t want to show when
your boat is on display. Make them
of a waterproof material which
matches the boat’s color scheme.
Supply them with draw strings of
ample length.

20. Classy looking spray skirts can. be
made from the same material that
you: used for the hole covers. Use
flexible cord to secure the skirt to
both you and the boat. The length
of the skirt is a compromise; make it
short, and it comes loose when you
bend. Make it long, and it acts like
a fish bowl and fills with water when-
ever it gets the chance. The best
spray skirts are made from expanded
neoprene material. This material is
expensive and comes in black, black,
and black, but stretches enough to
give you the best of both worlds.

With all these options rolling around in
our heads and a vision of the perfect C-2
clearly in mind, we are actually ready to
begin construction.

Preparing to build the canoe requires’
organizing a place to build, locating the
necessary supplies and a few helpers. The
essential elements in a building site are
sufficient room and the ability to maintain
the temperature above about 65°oThere
should be enough room to set up the mold,
cradled on sawhorses (both hull and deck
molds in decked boats) so that you can
easily walk around both ends. A side area
for resin mixing out of the traffic area is
handy too. For both polyester and epoxy
resins, the temperature should be main-
tained between 65° and 85°; epoxy can
be worked up to about 95° if you have
some experience; as the cure gets faster
with temperature. Good lighting is helpful,
but movable trouble lights can be used.

Other necessary supplies include paint
rollers, roller pans, paint brushes, coffee
cans, some large and sharp but expendable
scissors (don’t take the wife’s favorite
sewing ones), some rags, paint stir-sticks,
rubber gloves and plenty of newspapers.

The size of work crew can vary from 2
to. about 5 people. Two experienced people
can do a good job but they have to work
fast. If one of the builders is not exper-
ienced you should have at least 3 — better

HUT! MAY, 1973 15

Article contents & approved summaries (0)

No article summaries are available for this view.