May 1973 · Volume/issue not printed or unknown
May 1973 Magazine
Magazine · 24 pages
Search this issue
May 1973 Magazine
Captured text — scan page 18
Automatically captured text may contain recognition errors. Compare it with the original scan.
yet, 4 people. More than 5 people start to boat. The first layer of resin can be either centrated. ;
get.in the way. One system which has a tack coat, if epoxy is being used, or a Bulkheads ‘should be cut to the inside
worked well in our group is to help some- gel coat, if polyester is being used. Pig- shape of the seamed: C-2-.and held in
one build before doing your own and re- mented resin can be used to-saturate the _ place with fiberglass strips around the out-
cruit the one you helped; then you both _ first layer of cloth. For succeeding layers side edge. Additional flotation and stiffen-
have some experience and the technique _ the resin used to saturate the cloth should ing can also be gained by sealing similar
is passed on. have glass beads mixed in, except the last smaller bulkheads about 18 inches from
--,One lay-up which is quite good con- sealer coat. Using the glass beads in this either tip of the C-2.
sists of the equivalent of 5 layers of 74 or way adds stiffness to the laminate and The seat rings can be easily formed by
10 oz. fiberglass for an open canoe or C-2 _ saves resin, weight and cost. cutting the desired hole shape and holding
hull, or four layers for a C-2 deck. One Any flat areas of the above lay-up will about l-inch diameter tygon tubing (or
layer of 18 oz. roving can replace the last need to be stiffened with ribs. Three old garden hose) on the edge of the hole
two layers of cloth at some savings in cost lengthwise ribs, one in the center and one _ with tape using the tubing as amold. About
and gives a very nice texture to the inside 5 to 8 inches either side of center will 4 to 6 layers of bias cut fiberglass laid over
surface of the boat. If extra durability stiffen the bottom of a canoe’nicely. This 180° of arc of the tubing will form a nice
and/or light weight are desired,oneortwo center keelson should be about 3 to 4_ rigid ring. When the resin is cured, untape
of the middle layers of glass could be re- inches less than the total length oftheboat. the tubing and pull it out and file the re-
placed by the same number of layers of 4 The other two ribs need only be-4 to 6 maining fiberglass rim smooth.
oz. polypropylene. It isnotrecommended, inches long. Ribs can be formed using The trim-out is finished up by install-
however, to use polypropylene cloth with either half-round wood (2 pieces of quar- ing the seat style of your choice and knee
polyester resin. Thus, this last option ter round side by side) of about 1/4 to 3/8 bracing appropriate to your intended use
should be considered only when epoxy inch radius covered with three layers of for the canoe.
resin is being used. fiberglass bonding the rib in place. An- We recently figured the price of a C-2
Less resin and lighter weight will beex- other good ribbing material is Ethafoam at $150, including some very expensive
perienced if about 30% to 40% by volume about 3/8 inch thick by 1” wide with paisley deck fabric, three layers of poly-
glass beads are mixed with the resin during beveled edges and three layers of fiber- propylene fabric, epoxy resin, and all the
the lay-up. The only layers which should glass covering it. Similar transverse ribs paint rollers, brushes, etc. The only. com-
not have glass beads are the first layer will be needed to brace the deck of aC-2__ mercially built C-2 we’ve heard of recent-
which goes against the mold and the last at the back side of the passenger holes ly sells for over $400. The finished boat
layer which seals the inside surface of the where the paddlers weight will be con- weighed in at 55 pounds.
Pigmented resin
Select -
[| pigment
i How
Define the |_| Selectstyle || # | Select size | | select || winit (Both) IZ Flotation |Permanent
& LK and shape resin be colored method
boat mold of holes for holes system eee
? Verify cloth ?
1 2 4 5 : 6 |_| is compat-: 9
| able with [Inflatable
resin system
Select size 8
& Pattern ; Determine
shape for cloth. . source
center hole
3 10
\ Select Select
Select Select Select Select knee pad Will Select material. and
A lay-up mrontiyoet Bulkhead seat ring style and you use No | style for style for hole Definition
7 type® [7 Or ag «|| Placement [7] style & seat |) knee strap [| toe braces carrying [| ‘covers& [—] complete
technique ping & material type anchors ? handles spray skirts
11 12 dec 13 14 15 16 18 19
[Yes
Make toe
braces ad-
justable if
others will
use your
17 boat :
2 MAN WHITEWATER CANOE
A Guide for Design and Construction
16 HUT! MAY, 1973
Article contents & approved summaries (0)
No article summaries are available for this view.