← Back to The HUT

April 1974 · No. 7

April 1974 Magazine (No. 7)

Issue first-page cover

Magazine · 36 pages

April 1974 Magazine (No. 7)

Captured text — scan page 23

Automatically captured text may contain recognition errors. Compare it with the original scan.

Bostitch T-5 Tacker! The stress occurs be- After the interior was fiber glassed, attached to these blocks with screws and
cause the strip is flat on the bottomofthe thwart blocks were epoxyed to the hull epoxy glue. The thwarts were made from
canoe, is curving to match the keel, andis and covered with layers of 4-ounce cloth. 1%-inch x 3-inch billets of oak. By varying
being twisted almost 90 degrees to the Note the curvature and taper of these the depth or thickness of the thwart, sec-
vertical plane of the stem. Itiscompound- _ blocks shown in figure 9. The light cloth tion E - E, the thwart is sturdy, although
ed by the 38-inch width of the canoe.The works much easier in small sharp corner it looks almost fragile from the top view.
closeness of the templates allowed us to areas than the heavier cloth. One must re- The Lucius canoe had small deck pieces
omit stapling the strips between the tem- member to use enough layers for the de- placed between not over, the gunwale. We.
plates. We used 3/8-inch staples on the sired strength. The thwarts were then omitted the deck and placed wooden car-

strips into the templates. Cardboard was rying handles instead. The handles were
— sik esc pele = oo aay epoxyed and screwed through the gunwale
makes removal of the staples easier. Awor i

of caution on the T-5 \iodere if card- | TOP VIEW OF THWART a hel sate Gan oy dlinindia the
board IS used under the staple, and the i _spossible problem of the wax curing agent
stapler is held flush and tight to the strip, — | often present in other results. The project
no problem. If the stapler is tipped up yyy» 3" was satisfactory to us. The canoe meets
slightly to apply pressure on the strip and our requirements of a good, sturdy, stable
you hold the strip tight on the template y } family canoe. * , ,

as the staple is driven into the strip and a nd ee

template, there is so much power in the 3/4" 4" % SPECIFICATIONS

stapler that it will smash the staple into BE :

the wood and crush about half the depth length 16 feet

of your strip. This happens with or without width 38 inches
cardboard. So if a powerful stapler is used, ve

be sure to hold it tight on the strip for the “SHAPE TO depth @ center 12% inches

entire length of the stapler base. The Ar- gap | PO FAG finished weight

row and Swingline staplers I’ve used are

not this powerful and do not cause this

problem. Redwood keel and strips. Oak used on
Before fiberglassing the exterior, the chair, seat, thwarts, handles and gunwales.

wood screws holding the keel to templates

were removed. The holes were glued and

doweled. Water Putty was used to fill the

staple holes. We colored the putty and a

close match was obtained to our woodsam-

ple making sure that the putty and wood

matched when resin was applied. We had

ripped our strips from four planks. The

bundles of strips were kept separate and

applied equally on each side of the hull.

Their color varied little when dry. After . ; ; ; ;

puttying and fiberglassing, their colors Janet is a 20 yr. old Junior at Bowling Green University and is the

shone like a rainbow! The wood sample current USCA Mixed Champion.

that we matched the putty to was darker

than the wood in the other three planks.

The excessive darkness of the putty on

Tavanr Buck (without chair) 69 pounds

three-fourths of the canoe was discourag- And he STILL
ing. We could have saved a lot of time and can’t get along with
frustration by tinting the putty to any his partner?

red-bronze neutral shade and letting it go
at that.

The exterior of the hull was fiber
glassed from the edge of the keel outward,
with 7%-ounce cloth. The keel was over-
layed with layers of 4-ounce cloth placed :

diagonally to take advantage of the bias
action of the weave. We found that the
lighter cloth worked easy on a small ra-
ius, about the size of a wood pencil. Be-
fore the finish coat of resin was applied,
all edges were sanded and feathered into a
smooth surface.

As mentioned earlier, the stem piece is
flush with the interior strips. This makes
glassing the interior easier and smoother
than when a thinner stem piece is used.
Due to the width of the canoe, the 4-ounce
cloth was not wide enough to cover the
entire inside area. We used two lengths of
cloth and overlapped them at the bottom
of the canoe.

HUT! APRIL 1974 11

Article contents & approved summaries (0)

No article summaries are available for this view.