← Back to The HUT

September 1976 · Volume/issue not printed or unknown

September 1976 Magazine

Issue first-page cover

Magazine · 8 pages

For the full-resolution original, use Open PDF above. Your browser handles PDF zoom and navigation.

Scan page 5 of September 1976 Magazine
Searchable text for scan page 5

Tips on Building Whitewater Boats by Larry Johns

Some time ago HUT! Editor used by all Minnesota builders, hard to get. In my opinion,
Hilmar Wagner, after hearing although most people will tightly woven, pre-shrunk nylon
that my kayaks had won first, develop a few modifications of is stronger than poly and half the
second, and third places in the their own after building a boat or cost. It bonds as well or better
annual MCA Builders’ Contest, two. My advice to would-be than poly and uses less resin.
assumed that | must be a super builders is to read Charley Wal- It’s slightly harder to wet out—
builder and asked me to do an bridge’s book on building, and we’ve found it’s wise to end the
article on building whitewater then help an experienced builder nylon layers short of the seam
boats. Hilmar wasn’t aware that before starting your own boat. line, and that it’s easier to work
there were only four boats The process is quite simple, but the resin down through the
entered in the contest. Having the proper procedures must be nylon rather than up. The 6-5
five people in the family to keep followed to obtain the strongest, layup is a good _ standard,
supplied with kayaks, | have lightest boat possible. although a common variation is
built approximately 25 white- to use 3 layers of cloth and 2
water boats and helped with that Weight doesn’t necessarily nylon in the deck. This will make
many more in the past four mean strength; it’s very im- ita bit more flexible and slightly
years, and | have to admit that | portant that your kayak not be lighter. My son Tom wanted a
haven’t enjoyed a single minute too rigid. If a rock can’t flex your lightweight, responsive kayak
of the time involved. It’s an kayak, it will cut or break it. | for slalom racing, so we used 4-
unpleasant task, but it has its personally see no reason for a ounce cloth in place of 6. We
rewards. kayak to weigh more than 25 added ribs of roving strands to

pounds out of the mold. This stiffen the laminate and ended

Building your own boat will cost

means that with the seat, end up with a kayak that weighed
eee toe ee pours, grab loops, foot braces, 16 1/2 pounds out of the mold.
“ . naa tacts wica as and flotation bags, it will end up This is probably too light for
Sat eae Enos, seed weighing less than 30 pounds. aggressive cruising for most
—— a stronger kayaks To obtain a 25-pound boat, | people, but it has held up very
You can design a layup to fit would suggest a layup with 4 well. | believe that the 6-5 layup
your needs, whether it’s‘an 18- layers of 6-ounce fiberglass cloth using 7:1/2-ounce cloth would be
— racing beret. area el L-erenneitl and 2 nylon in the hull, 4 layers too rigid and would not hold up
craft weighing 25 pounds, or a of 6-ounce cloth and 1 nylon in as well as the one built with
; 2 the deck. To figure the approxi- 6-ounce.
32-pound kayak that’s as flexible mate out-of-the-mold weight, |
Sele uel the avide at total the number of ounces in the The layup can be greatly altered
paddling a beat you've bullt hull and deck—8 layers of if you use Kevlar or S-glass.
vaneelt, Tt may be rumefahe- 6-ounce = 48, 3 layers of 4-ounce Concerning the use of Kevlar,
mill to anyone else, but to the pene OF 2 Biel @ Ee, & "m not at all sure that the
arifider-ciatar it’s. a woke of factor of 42 per cent of the total results justify the added ex-
art—very likely fun Ciead: evar will give you the approximate pense, which can double the
built weight. In this case, 42% x 60 = cost. Kevlar-reinforced kayaks
. 25.2 pounds. This works very seem to have more of a delam-
| don’t intend to go into step-by- well for me. A boat with this ination problem and suffer as
step instructions on how to laminate will be sturdy enough much or more damage than their
build, but | would like to express for cruising and light enough for fibergkass/nylon or fiberglass/
some of my own observations all but the most serious racer. | poly counterparts. This is my
and recommendations. Some of ._ add several patches in the bow own opinion, and I’m sure there
the finest whitewater boats built and stern, which are the areas are some who don’t concur. |
are by Minnesota paddlers, most frequently damaged. | believe that Kevlar can be best
mostly due to the expertise of suggested using nylon for utilized for the construction of
Bob Haug, the first builder- flexibility. l’ve used it in several super light racing boats, but
innovator in the Midwest. The boats and | prefer it to poly- adds little to a cruising weight
methods developed by Bob are propylene, which is becoming boat. j

[UT PAGEE SEPTEMBER 1976

Article contents & approved summaries (0)

No article summaries are available for this view.