April 1977 · Volume/issue not printed or unknown
April 1977 Magazine
Magazine · 20 pages
Search this issue
April 1977 Magazine
Captured text — scan page 17
Automatically captured text may contain recognition errors. Compare it with the original scan.
Then shape and compound taper the then two handle/blade stiffening mem-.
NOS Ee eee blade with a hand plane or equivalent bers of 3/8-1/2” thick strips are edge
WHEN RESIN IS CURED and shape the handle as before. glued as follows:
-—— a
Pl oe i=N Zz : Cc >
z gA = S 7
SS
= At_S = =
=
Le jo— 12°"
i" ——_s Fig. 14
= GLASS STRANDS A-A
AND RESIN
Fig. 9 a These should be planed flat on one side,
B-B ste. 4 and the full size blade planed flat on
‘11 both sides. Next glue the stiffeners to
After cured pull off waxed paper and either side of the blade and handle.
d flush.
amma After this style is shaped, about 3 layers
of glass over the end and corners of the
blade will save the paddle from damage
on the rocks. To do this cut bias strips
about 3” x 18” and wrap them over the
The next step is to put fiberglass on
both sides (faces) of the blade. To go
smoothly over the raised handle, the glass
cloth must be cut on the bias of the
weave. Another method is to put a bias Fig. 15
strip over just the handle area, then cover
the remainder of the blade up to where
the handl d using four small- ; : 5
at a Read SESSA NEN PAID ED A | fa The grip can be built up as in the other
styles. Then the finishing and shaping can
be started. The blade should be tapered
both lengthwise and side to side as in the
area of the blade where bracing is needed.
A little trimming, sanding, and a coat
of polyurethane varnish over the non- —=>
glassed areas and the paddle is finished. A-A ces evel
A second style like the commercial ee aan a a q very
Cadorette comes out a little heavier, Fig. 12 Od pattern as follows:
wastes more lumber and requires a little
more care and time in finishing but is
considered stronger and more attractive Make the strips slightly different widths
by some people. To make this paddle, gy all the edges don’t occur at the same
first laminate the handle from | 1/8” to place. This will make a less abrupt tran-
1 1/4” wide strips to yield a thickness of — sition edge. After the resin has cured, SS
1” to 1 1/8” wide. Then the blade is sand the edges smooth. When all the shap- =a =
laminated to shape using thicker stock, jing and sanding is finished, varnish with ————
1” thick near the center and 1/2” thick polyurethane the exposed wood parts of
near the edges. also build up the handle. the paddle and it’s done.
A third style (as made by Clements) is
similar to the Cadorette style but does
not require as thick strips (less waste
and finishing) as the second style but
requires a little more care in finish- Again, the end and corners should be
ing. The blade and handle are edge glued glassed for strength against abuse as was
Fig. 16
of 3/8” strips: done on the second style.
>A
[
=
= [ 3 col
These are the only three laminating
— Lt — —* methods I’ve tried, and I guess I like
E =) the first one best for paddle weight, feel,
A —— and ease of finishing. All give plenty of
strength, especially if the blade and
coomooop
A-A
handle are fiberglassed.
Fig. 10 % Fig. 13. Happy paddling.
Article contents & approved summaries (0)
No article summaries are available for this view.