May 1977 · Volume/issue not printed or unknown
May 1977 Magazine
Magazine · 20 pages
Search this issue
May 1977 Magazine
Captured text — scan page 15
Automatically captured text may contain recognition errors. Compare it with the original scan.
The cost of a hank of cane does vary but normally can be
obtained within the range of from $8.25 to $12.00. A hank
should provide enough cane to weave at least two sets of
canoe seats. The cane can be purchased in different widths
ranging from “Carriage”, the narrowest, to “Common”, the
widest. I prefer the width most used when caning chairs,
called “Fine”. This width is easy to work, has good strength
and weaves into visually pleasing patterns.
You can also make cane canoe seats by using machine
woven or manufactured webbing by way of a spline method.
This method is usually explained in the same booklets which
give instructions for the hand weaving method. If you do not
have the time or desire to weave your own canoe seats,
complete hand woven seats may be obtained from Betty
Ketter, 101 79th Avenue North, Minneapolis, MN 55444,
(612) 561-2208.
Thope that you will try your hand at weaving your own
canoe seats. Caning is a skill which is not difficult to master,
requires only a few simple tools and costs relatively little.
The woven seats will add to your pride of craftsmanship and
to the beauty of your completed canoe.
Particular attention should be given to the directions
which warn of errors to be avoided. Minor errors can creep
in unobstrusively but are usually undetectable in the overall
pattern when the weaving is completed. Major errors cannot
be hidden quite as easily and will require that the weaving
be started over from the point of the error. Errors are not
catastrophic and should not prevent you from trying your
hand at weaving with cane.
To cane or not to cane? That is aquestion facing most
builders of wood strip canoes. The article which follows is
intended to pique your interest in caning your own canoe
seats. Although I will not go into the details of how to weave
with cane, I will try to answer a few of the most commonly
asked questions about caning.
Caning of the seats can be done at any time -- before,
during or after the hull has been built. Once the frames have
been made, the holes drilled and the frame finished, the
weaving may begin. It is advisable that you varnish the
frame before weaving in order to protect the wood from oil
and dirt while you are working. Also, it is much easier to
apply the varnish uniformly over the entire frame while the
cane is not in the way.
Of the various types of seating materials available
(rope, leather, plastic cane or webbing and natural cane), I
believe that only natural cane adds the special finishing
touch to a wood strip canoe. Cane and wood are
complementary materials which, when combined, create a
unity of design for a canoe of great natural beauty.
The weaving process is not messy and may be done
anywhere in the home, from the workshop to the
livingroom. Only a few, inexpensive tools are required: a
scratch awl for enlarging the holes, a pair of scissors or a
small side cutters for cutting the cane, wooden pegs for
securing the cane in the holes and a bowl or jar containing
glycerin and water in which the cane is soaked to increase its
flexibility. A small “C” clamp will come in handy to clamp
the frame to a table or bench so that you may use both hands
to weave.
A cane canoe seat is both strong and comfortable to sit
on. The open weave possesses a natural springiness and
permits air to circulate, making the canoe seat more
comfortable when paddling. The woven cane holds up to the
weather very well, but a couple of thin coats of varnish will
add to its many years of trouble free service. If a strand of
cane should break, you can very easily remove the broken
strand and reweave a new one in its place.
Caning is not a difficult skill to acquire. As with the
building of a strip canoe, it can be learned by individual
practice.
Observing the techniques of an experienced cane
weaver, however, can improve your skills, your confidence
and ultimately the quality of your weaving.
For the beginner, caning can be undertaken with no
more background than that obtained from carefully studying
the printed directions and illustrations of such pamphlets as
Cane Seats for Chairs by Ruth B. Comstock and Seat
Weaving by L. Day Perry. Caning instruction pamphlets can
be purchased in most craft and hobby shops or they may be
checked out at your local library. While these booklets were
written primarily to explain how to cane chairs, the same
steps can be used when weaving your canoe seats. By paying
close attention to the instructions as your weaving
progresses, you should have no unusual difficulty in caning a Clyde demonstrating caneing at the Rosedale Builder's
very acceptable canoe seat on your first attempt. Show. Photo by Dean Miller
Page 13
Article contents & approved summaries (0)
No article summaries are available for this view.