← Back to The HUT

March 1982 · Volume/issue not printed or unknown

March 1982 Magazine

Issue first-page cover

Magazine · 16 pages

March 1982 Magazine

Captured text — scan page 11

Automatically captured text may contain recognition errors. Compare it with the original scan.

First strips follow the shearline

Figure 1

Builders Corner

by Bob Brown

This month, before I start, I'd like to recommend some
further reading.

————— a _

One book that many people have been reading is First strips are horizontal

"Woodstrippers Guide to Canoe Building" by David with the ends filled in later

Hazen. This book is quite good, although his methods — = =|
and mine differ somewhat. Hazen has included plans [ ; —
for some boats of his design. He has lots of good Figure 2 St |

pictures and drawings. Many people have built canoes
from his instructions only.

Another book that I've run across is Gil Gilpatrick's
book "How to Build a Strip Canoe." Gilpatrick wrote
his book, I believe, to be used as a high school text;
it would do this well. His book is somewhat crude,
but he has very good pictures to explain his
procedures. Gilpatrick has also included plans with
his book. They look like poor designs, hardly worth
your time to build.

Overbeveled
a seams

Offsetting a bulge back
to the proper line

7

- ; —~— Area bulged outward
Figure 3

The best book available, of course, is the MCA
Building Manual. If you haven't read it, you should.
If you read it years ago, read it again. Each time I
reread the MCA book, I find things that passed me by
the first time. This manual is a simple book, but it is
very complete.

Figure 4

* * *

I promised that we would start on stripping this
month, so let's check over what we have done. Our
forms should be set up and trued. All of the center
lines should match up to the string. The rocker that
the plans call for is in fact there and uniform.

Wedges added in to reduce hooked ends

Take a good long look and see if everything is ready. Figure 5
Did you tape your forms? I've forgotten this step
more times than I'd like to admit.

Applying an even bead of glue from a squeeze bottle

If you want the hull to be removed from the forms comes with practice as will giving the slight

when you're done, you'd better put a band of masking compression on each joint as you staple the strip.

tape on the outer edges of each form. This tape

helps prevent the strips from gluing themselves to the I staple the strip to each form first starting from the

forms. center. Next I go back with my small gun and staple
two or three places between forms, being careful to

You must decide at this time which method of press the strips together as I staple.

strippi ou plan to use.
Pping you P I like to wash off any excess glue right away before

The most common method is to start by fastening your I start the next strip. I keep a bucket of water
first strip to the forms at the gunnel, bending it to handy and use a rough fabric like terry cloth. Any
match the curve of the sheer (see Figure 1). This glue remaining when you glass the hull will show up as
method works well on the Guide model, the MCA 14, a light colored blotch on the finished hull. Wipe up
and on most boats with some rocker. your work good and change water often.

On the Explorer and many straight-keeled boats, I like So far, I've said nothing about beveling strips. You
to install my first strip horizontally starting at the may need to bevel some as you get into the tight
gunnel height in the center of the boat (see Figure 2). curves, but try to keep it to a minimum. Most
All of the stripping is kept horizontal. The curve of beginners over-bevel (see Figure 3) and don't realize
the sheer is added onto the bottom after you are part they're doing it until they pull the hull off the form.

wey Sy The side. I generally try to keep the inside of the strips flush.

It's much easier to smooth up the outside with your
sanding. One exception to this is where I'm trying to
remove bulges. Bulges may occur as you are
stripping, and this is a good reason to stand back and
look over your work from a distance. Do this quite
often, as the sooner you notice a bulge, the easier it
will be to remove.

Once the first strip is in place on both sides (with
either method), the operation becomes repetitious.
You run a bead of glue on the previous strip, add a
strip and staple the two strips together. I like to
alternate from side to side.

I use two staplers (both Arrows), one with 9/16"
staples to hold the strips to the form, and a smaller
gun with 1/4" staples to fasten the strips to each
other.

When I'm removing a bulge, I try to make a strip
return to its proper place by offsetting the strip

11 Cont. on Pg. 15

Article contents & approved summaries (0)

No article summaries are available for this view.