← Back to The HUT

May 1982 · Volume/issue not printed or unknown

May 1982 Magazine

Issue first-page cover

Magazine · 16 pages

For the full-resolution original, use Open PDF above. Your browser handles PDF zoom and navigation.

Scan page 7 of May 1982 Magazine
Searchable text for scan page 7

7 9 My normal procedure is to combine the staple pulling and

15 TVS” the surforming. I will spend a half hour pulling staples

out of an area. By this time my fingers are getting ready
for a break so I stop and grab the surform to clean up the

staple-free area. I alternate between these two jobs until
the hull is clean.

by Bob Brown

You have something that looks like a boat, but what a

mess. Somewhere in the building process you went The ends are also treated with the surform. I first trim
through three boxes of staples and a half a quart of the ends roughly to shape by trimming off any extra
glue. Don't feel bad, we all do the same. length on any strips till I get close to my desired end
shape. Next I use the surform to finish the shaping and

The best way to pull staples is to use less in the first smoothing. Do all the cutting toward the ends and you
place. That's OK for the next boat, but right now we are should get no splintering.

still on number one.

. I like to shape my ends up fairly sharp but the glass won't
I use several tools when pulling staples, but the one used fit around a knife edge. Shape your ends to a 1/8 or 1/4

most is a church key. I flatten the point and file it thin radius and the bias strips will contour over this nicely.
and smooth. This works quite well; add a handle and

you've a great tool. After I've gone over the whole exterior of the hull and

gotten it as smooth as the surform will do, I start

Sometimes a staple will break off leaving one leg still in sanding. Sanding any sooner is a waste of your time.

the wood. I find that long nose pliers or side cutters pull

these out well. I start sanding with a 40 grit paper in an orbital sander. I
. go over the entire hull with this to remove scratches left

Take your time pulling staples; do a small area at a time by the surform.

and make sure it is clean before going on. Any missed

staples or parts are hard on the tools that you use for When all of the heavy scratches are sanded out, I change

cleaning the hull. to 60 grit paper and remove scratches left by the 40 grit.

Smoothing up the hull isn't a bad job. The first thing that Some builders try to get a silky finish prior to glassing.

must be done is to get rid of the glue. Look at the texture of 7.5 oz. fiberglass and you should

see how silly a super smooth finish is.
If you didn't wipe up your glue real good you may have

beads of glue sticking out all over. The best tool I've You can, if you wish, go over the hull with wood fibers
found to clean this mess is asurform file. I prefer the 8" and try to fill all the holes left by the staples and nails. I
straight one. The glue will dull this tool fast. I always don't.

use an old blade until all the glue has been removed.

Then I install a new blade to finish the smoothing If you do want to fill the holes with a filler, don't try to
operation. match the dry wood. Wet ascrap of your wood with resin

and try to match this darkened sample.
The surform works best at about a 45° angle to the grain

of the wood. This tool knocks down any hills quite fast, Many small holes can be filled by dampening the wood

but you need have little fear of cutting through the hull. =a hole. It will swell the wood; this often will close
e hole.

Belt and disk sanders scare me. Many builders start

sanding with a belt sander only to find that they went The same treatment with water will often push out

completely through the hull. Disks are really no better. dents. Often the staples have dented the wood and you

You will not get a smooth job with these sanders as they still have a mark after much sanding.

will often cause waviness that was not there originally.

, If you have time to dry the hull again before glassing, I
High speed sanders have another problem—they melt the like to sponge off the hull. Remember now that Elmers
glue rather than cut it off. These sanders smear the glue glue isn't waterproof. Go easy.

around and clog up the paper.

Holes will close and dents will pop out. Any glue still on

the wood will show as a light spot on the wet wood.
Better to find these spots now than find them under your

The exact reason for the state's appeal of this law has glass.

never been clear. Governor Al Quie has said he believed

the law was a federal intrusion on the state's rights. Remember any spots that showed smeared glue or the
DNR Commissioner Joe Alexander argued that he wanted lacquers from your filler and re-sand in these areas.
to maintain state jurisdiction in the BWCA to prevent any After you're satisfied that you have no smears left, go
mining in the area. Even ‘though the BWCA Act over the entire hull again with 60 grit.

specifically prohibits mining, Alexander feared this ban

might be lifted by the Reagan administration. Next clean up your shop, dust off the hull and get ready

to do some glassing.
Environmentalists assert that the state challenged the

law as a way of appeasing residents of northeastern Some folks prime the hull with lacquer or shellac. I have

Minnesota who were angry over the restrictions on mixed feelings about this prime coat.

motorized travel. They charge that the state changed its .. . .

basic position on the BWCAW after Quie and Alexander If your wood is fairly resinous, the primer may make the

met in 1979 with those area residents. difference between a good glassing job and a failure. If
your wood is dry and resin free, then I feel that the best

The decision by the high court was a clear victory for the bond can be made by letting your resin soak into the

forest service and environmentalists. The forest service surface of the wood - the primer prohibits this.

Next issue, we glass. Right now spring is really here, my
C.J. is loaded, and the Mississippi is calling.

among these groups were the Sierra Club, Friends of the
Boundary Waters Wilderness, the Isaac Walton League and

was supported by 11 environmental groups. Included |
the Wilderness Society.

Article contents & approved summaries (0)

No article summaries are available for this view.