← Back to The HUT

October 1982 · Volume/issue not printed or unknown

October 1982 Magazine

Issue first-page cover

Magazine · 16 pages

For the full-resolution original, use Open PDF above. Your browser handles PDF zoom and navigation.

Scan page 7 of October 1982 Magazine
Searchable text for scan page 7

iF I am very happy with the way the canoe paddles. It is a
, very efficient, fun canoe, with sufficient volume for light
: a Co tripping. If you are used to flat bottom canoes, you may
i ie) THY not like it.
If you are interested in this construction technique, give
An Alternative Method of Canoe Construction me a call and profit from my mistakes. Mike Ludvigsen,
884-0033.
by Michael Ludvigsen

Foam is available from:
It is possible to construct a one off canoe using a

composite foam core/fiberglass construction. Some of Wicks Aircraft Supply

the drawbacks to conventional fiberglass construction are Highland, Iinois 62249

the expense of high quality PVC foam and the time and Phone: 618-654-7447

expense involved in making the female mold. It is Clark Foam - 4.5 lb/ft3

possible to get around this by constructing a male mold 24" x 96" x 1/4" sheet @ $10.60/sheet
on a strong back in a manner identical to conventional

woodstrip construction. Information on construction:

When the cross sections are up, take a router and cut Clark Craft Boat Company

grooves every couple of inches and lay 3/8-inch stringers 16 Aqualane

the length of the forms, flush with the edges of the cross Tonawanda, New York 14150
sections. Use a 1/4-inch polyurethane foam that comes Booklet on fiberglass boat construction @ $5
in 2-foot by 8-foot sheets to staple to the forms and

stringers. The foam is thin enough to take slight Local sources of supply:

compound curves, but where there is a large amount of

compound curvature, it is good to work with 1-foot or Mrs. Ketter can get some supplies from Winona
possibly 1/2-foot wood strips. The edges of the foam can and carries West Systems products.

be glued with a construction adhesive if desired.

Polyurethane foams don't have good strength in IASCO

compression, and it is necessary to remove the foam in 5724 West 36th Street

the football area if hitting a lot of rocks is anticipated. Minneapolis, MN 55416 (by Hoigaards)
If the foam collapses, the bottom of the canoe will lose 612-920-7393

its rigidity.

To facilitate removal, coat the area to be removed with a

couple of heavy coats of cornuba wax and a layer of presents
PVA. Foam absorbs a great deal of resin, and it is neces- TOM JOHNSON’S
sary to coat the foam with a mixture of microballons and

resin. One cup microballons to two cups of foam seemed

to work well. When this has hardened, sand it lightly and
lay up the fiberglass on the outside. When the outside is
completed, pop the canoe off of the mold. Pull the
staples out with a pliers from the inside, remove the A revolutionary breakthrough
foam from the football area, and fiberglass the inside. in roto-molded kayak design

Ribs have to be installed, and the seats, thwarts, and

gunnels are installed conventionally. A flatter cross sectional hull

profile reaches the absolute
limits of plastic technology. .

The cost of this method of construction seems to be © greater
about equivalent to the cost of a wooden canoe. The stability
foam costs less than wood, but more fiberglass and resin ° an ee a
are used. Disadvantages are that the foam doesn't have e less drag
very high strength under compression, doesn't have a very coefficient
high shear strength, doesn't have the aesthetic appeal of for faster
wood, and it takes longer to make the mold due to the turns
necessity of installing the stringers. Totally

outfitted with
minicell foam

Advantages are that the foam lays up faster than wood- © low weight:

strips; an all fiberglass bottom will usually take more only 34 Ibs
abuse than a wood/fiberglass bottom; once the mold is © no wear
made, several people could use it with the second canoe er
being started as soon as the first is popped; and flotation and ball
is built into the canoe so that no flotation chambers are © unique sized
necessary. hip brace
system for
This method was used to construct the 15-foot C-1 of al
Karl Ketter's design. The canoe has three layers of 7-1/2 ization
oz. cloth and a total of ten layers in the bottom at the S 479 00
bow and stern. The canoe has gunnels and thwarts cluscshinping Hydra
installed, but no seat or foot braces yet. It weighs 36 lbs. At Hydra P.O. Box 669
and should finish at less than 45 lbs. If more care, skill, Dealers Athens Tennessee
and less materials were used in the construction, it could Nationwide Ps veces, nee

be made lighter.

Article contents & approved summaries (0)

No article summaries are available for this view.