← Back to The HUT

April 1983 · Vol. 19 No. 4

April 1983 Magazine (Vol. 19 No. 4)

Issue first-page cover

Magazine · 20 pages

For the full-resolution original, use Open PDF above. Your browser handles PDF zoom and navigation.

Scan page 4 of April 1983 Magazine (Vol. 19 No. 4)
Searchable text for scan page 4

CLIFF’S CORNER

Bob Brown, Darrell Foss and I have built
more than a dozen woodstrip canoes. Yet only
recently have we gotten our act together on
how to fiberglass. Over the years we've learned
a lot about durability, delamination, strength
. .- and what not to do! Hopefully, interested
builders ean learn from our mistakes.

Our earliest boats were constructed with
a layer of 72-ounce cloth outside and a layer
of 4-ounce cloth inside. We used MCA polyester
resin and had few problems. Our glassing pro-
cedure was:

1. Sand the hull thoroughly with an orbital
sander with 60 grit paper.

2. Set the glass cloth (wrinkle-free) over the
sanded hull and apply "finishing" resin (resin
with wax mixed in) to the cloth with a
short-napped paint roller.

3. After the resin is rolled on, apply a second
coat of "hot mix" resin to the glass with
the roller. This step should fill the weave
of the fabric.

4. Allow the resin to cure thoroughly, then
sand and varnish.

We encountered few problems with this
procedure, save for an occasional small starved
area.

Then we got the idea that using two layers
of 4-ounce cloth outside would be better than
a single layer of 7z-ounce stuff. Glass to resin
ratio would be higher and the tight weave of
_the cloth should result in a quicker and easier
high final finish.

So we tried it. We glassed three canoes in
this manner according to the procedure above.
The results were disappointing. Every canoe
exhibited resin starved areas. In fact, I nearly
burned "Mantoy" (the CJ solo prototype) because
it looked so bad. Only soothing encouragement
by Bob and Darrell enticed me to finish the
boat—which paddled so well I kept it.

I learned that durability of the double
4-ounce glass was actually less than one layer
of 72 ... even less than a single layer of 6-
ounce (according to Gene Jensen). The light-
weight glass slit like paper on sharp rocks.

It did make for a structurally strong and stiff

lightweight boat, but that was all. A heavier

weave was needed to combat abrasion.

ONG LI

& Ye,, HANDCRAFTED CANOE
€s PADDLES

BENT SHAFT $41.95

Custom Canoe Paddles STRAIGHT SHAFT $37.95
(SHIPPING NOT INCLUDED)

1076 EDMUND AVE. ST PAUL. MN $5104 612-645-9453

4 HUT!

Darrell recently completed a 12-foot
solo canoe of his design using the "Jensen
method." Perfect! We heartily reeommend
the procedure. Dry wood must be primed before
glassing to prevent the occurrence of starved
areas!

While Darrell was experimenting, I tried
WEST Epoxy. I had just completed a beautiful
142-foot solo boat designed for me by Bob
Brown. The western red cedar hull was gorgeous
and the evolved design suggested the boat would
be a magnificent cruiser. I decided to take a
chance on the 52-dollar-a-gallon epoxy.

But I was concerned about the epoxy-
related horror stories—rashes, respiratory and
physical disorders. The WEST literature
stressed the low toxicity of the product but
did advise wearing barrier cream and gloves.
No mention was made of using a "respirator."

I ealled Lew Miller—president of Rice Creek

Boat Works. Lew had built dozens of epoxy

boats and was a great believer in the stuff.

"It's safe," said Lew. "I've used it in my base-

ment!"

Now... after using the product ['m-most
enthusiastic. It's nearly odorless and foolproof.
It sands almost as easily as polyester but has
much superior abrasion and peel strength.
Unique, is a clever pump which meters out
precise quantities of the resin with no waste
or spillage. It's trouble-free—no delamination,
no starvation, and high flexibility. I doubt if
I'll build another polyester boat.

Using WEST epoxy is similar to glassing
with polyester with these exceptions:

1. Roll ona prime coat with a foam roller.

2. Sand the hull lightly after the prime coat
cures.

3. Place the glass on the primed and sanded
hull and squeegee on the epoxy. Don't
use a roller for this operation; it traps
too much air which may cause a cloudy
finish. The flexible plastic squeegees that
are recommended work great.

4. After eure, sand (electric drill with 80-
grit disk) the top few microns of cloth
and resin—enough to get a reasonably
smooth surface.

5. Roll on (foam roller) enough epoxy to fill
the fabric weave. Allow to cure.

6. If the weave is completely filled you may
sand and apply two coats of varnish which
contains ultraviolet inhibitors. If the weave
is not filled, sand again with the electric
drill and apply a leveling coat of epoxy.

‘7. Stand back and admire your work. You've
done a perfect job! Cliff Jacobson a

Article contents & approved summaries (0)

No article summaries are available for this view.