May 1983 · Vol. 19 No. 5
May 1983 Magazine (Vol. 19 No. 5)
Magazine · 20 pages
Search this issue
For the full-resolution original, use Open PDF above. Your browser handles PDF zoom and navigation.
Searchable text for scan page 4
BUILDER’S CORNER
By installing our bias strips first we got glass is wet out because the glass will turn
a good lesson about working with fiberglass. transparent. As soon as this happens, move
Now comes the time to do the main sheet on on to the next area.
the outside of the hull. Work from the center outwards toward
Sand down any large lumps on the bias the gunnels, completing a band across the hull.
strips and wipe them off with acetone, removing Expand this band keeping a fairly straight work-
any wax from the surface. Smooth out the glass ing edge. Begin working towards one end and
over the entire hull and lay out any remaining go that direction for a few minutes. Now square
bias strips in a handy place. Make sure that up what you've done and move to the other
the temperature and humidity are right before edge and work that line for a while. You want
you decide to glass. to keep your edges moving so that you don't
Be sure that you have time (3-4 hours) so get a curing edge, don't let either sit for long.
that you're not rushed. The same for your > _Keep an eye open for any sign of the resin
helpers. Once you start glassing, you can't starting to jell. Discard any resin that is start-
stop until it is completed. ~—Z ing to set up.
The size of the batches depends on the/ If your first pot shows no sign of setting
size of your crew and their experience. Begin- in the pot, you may choose to make the second
ners should settle for pints at first until they batch slightly hotter. Continue this operation
get a feel for the operation. wetting out with the roller and stretching with
I never mix over a quart, even with exper- © your brush until you approach the ends.
ienced help. Pour a small puddle from your When you get within inches of the ends,
first batch on the boat bottom near the center. stop and trim. Cut the fabric 4 to 2 inch short
Use this puddle to wet out your rollers. As of the end of the boat. Wet out the remaining
soon as they are wet out, start to spread this glass and smooth it down over the bias pieces.
resin. Start by expanding the size of the first When both ends are done, add all remaining
puddle, working the resin through the fabric bias strips. Immediately after finishing the
into the wood below. You will know when the first coat apply a second coat. The center
section may be beginning to set up. If it hasn't,
make your second coat hotter still.
. You may find "starved" areas as some
America’s of the resin has left the glass and soaked into
Number the wood. The second coat should refill the
weave of the fabric and eliminate any dry spots.
Check for any remaining dry spots and add
more only where needed. Clean your tools
and yourselves and get some fresh air.
Check from time to time on your cure.
If you catch it right (at the green cure stage)
you can trim off the extra glass with a razor
blade tool.
Pa eae C3 a ™ If the cure is slow, add heat. If it is very
Res Artin ” ai Mirage™ slow (2-3 hours), paint on a hotter coat. Keep
SRE an Dancer™ the hull warm and dry until it has cured and
~ Eclipse™ then give it a day more before popping it from
HD-4™ the forms. I usually sand the hull and give it
a third coat, but not until the inside is done.
RELI. Accessories™ There are many alternate methods. My
7410 W. 98th St.
Bloomington, Minn. 55420 method has worked well for me. One of the
best alternatives that I've heard of is to prime
Midwest Mountaineering the hull with laminating resin (no wax). The
309 Cedar Ave. S. surface stays sticky and the fabric is layed
Minneapolis, Minn. 55454 :
erce tion out and smoothed well on this tacky surface.
Scheels Hardware & Sports p P The glass is wet out and its surface also remains
505 Center Ave Send — color catalog: tacky.
fs erception 5 F
Moorehead, Minn. 56560 Dept. MCA, P.O. Box 686 Any bias strips or other add-ons are
"BBO Eee applied. To cure the surface, mix a batch with
wax added in and coat the surface.Bob Brown ug
4 HUT!
Article contents & approved summaries (0)
No article summaries are available for this view.