← Back to The HUT

July 1983 · Vol. 19 No. 7

July 1983 Magazine (Vol. 19 No. 7)

Issue first-page cover

Magazine · 20 pages

July 1983 Magazine (Vol. 19 No. 7)

Captured text — scan page 14

Automatically captured text may contain recognition errors. Compare it with the original scan.

BUILDER’S CORNER

Set up an area for mixing—any table or First shake up the resin can to mix in
work bench works. Cover your table and pro- any wax, then pour your half pint. Add the
tect it from spills. Have solvents handy for catalist about 13 to 3 ml. of catalyst with an
clean-up during and after the job is done. Ace- eyedropper, mix thoroughly.
tone is good for cleaning but is very flammable. Use a cheap 1" bruch for installing these
I keep the acetone outside. A good cleaner strips. Lay a narrowstrip on the stem, near
can be made from ammonia and dish detergent. the bottom, and proceed to wet it out with
This is much safer and cheaper than acetone. resin. Once started the resin will hold the strip
I have both on hand before I start. onto the boat as you continue to wet it out.
The last thing I do before starting to glass More working time can be had by adding
is to brush off and vacuum the hull. Remove a little less catalyst. If you used all the first
any sawdust or other contaminants. batch without jelling the resin, you may add
Now you're ready to start glassing. slightly more to speed the cure.
I don't prime my boats. If you choose Take your brush out of the solvent and
to prime I'll recommend doing it with resin. shake it clean. Go back to work on the ends.
It is my opinion that the best bond for polyester When you have completed the end with 2 layers,
resin is polyester resin. Some people prime look for starved-looking spots and rewet them.
their wood with lacquer or shellac. Some of Remember we didn't prime so some of the resin
us don't prime at all. will soak into the wood. Replace it.
I spread the glass out over the boat from Wash out your brush and clean up. Don't
end to end and trim for length. Smooth out throw out the extra resin. As the resin cures
the cloth and center it so it drapes over the it will turn hazy as the wax comes to the sur-
sides uniformly. Be sure that the fabric is flat face. Check the resin from time to time and
and smooth all over. Trim off any cloth that you will see how it cures. The surplus resin
“hangs more than an inch below the gunnels. in the pot should begin to cure first because
Keep the large trimmings clean as you will it's thicker. Any glass that hangs below the

be using them. The trimmings will usually be gunnel makes a good gauge to tell you the condi-
four triangular pieces of cloth. From these tion of the cure.

pieces I will make my bias strips (see Fig. 1). The resin reaches a point where it's

I cut strips of fabric at a 45° angle to the weave rubbery—it no longer runs but it will still bend
of the fabric as shown. These strips vary from freely. It is at this stage that you can trim

2 to 5 or 6 inches wide. Make many different with a razor blade. If the resin hardens com-
width strips. pletely before you can trim, don't worry, at

The strips that I make from scraps are least you know you got the right mixture. If
not usually long enough to completely wrap you are oa waiting for a cure after an hour
around the stems. Usually they will go half- you didn't have enough catalyst for the temp.
way and overlap halfway around. I like to use Try adding heat to the surface with a heat lamp,
these as the overlap causes extra layers of this sometimes helps. ae
glass. After another hour if the resin still hasn't

I install 4 or 5 full layers of bias cut fab- cured, check the surplus in the pot. It this —
ric on each end. The area that has the overlaps also hasn't cured, it's time to take some action.
ends up with 8 or 10 layers. This makes a dandy Get out your tools and mix up a small
erunch pad. I you are a first-time builder and batch, very hot. Double the catalyst from the
are not confident in glassing, I reeommend last batch and paint this unto the uncured sur-
that you start with a small project. Rather face. This will often cause a cure. Then, if
than do the entire bottom try glassing only the resin has not cured after a couple more
a couple bias strips on each end. This is a great hours, make a test batch. Mix a very small
place to practice. pot with 4-5 times the original catalyst. By

Fold back the main sheet of cloth and now if this batch hasn't cured after a couple
bare the ends of the boat. Mix a small batch hours, peel off the strips you've installed and
of resin, about a half pint in a container twice find an expert. Something is very wrong.
that large to give lots of splash room. Mix Bob Brown #&
thoroughly.

14 HUT!

Article contents & approved summaries (0)

No article summaries are available for this view.