← Back to The HUT

June 1984 · Vol. 20 No. 6

June 1984 Magazine (Vol. 20 No. 6)

Issue first-page cover

Magazine · 16 pages

June 1984 Magazine (Vol. 20 No. 6)

Captured text — scan page 11

Automatically captured text may contain recognition errors. Compare it with the original scan.

Catalyst is not necessarily all the other than resin (yes, this happens). A

same strength. It looses strength with friend of mine painted on two coats of
age. It ages very fast in bright Naval Jelly mixed with catalyst before he
sunlight. If you set your catalyst bottle discovered his mistake.

up on a window sill to keep it out of Starved spots can develop in your job,
reach of the children you could have a especially if you didn't prime the hull
problem. Old resin gets lumpy, you can first. These spots are obvious as the

see this when you pour it. Old catalyst cloth begins to reappear after it was once
still looks like so much water, this makes wet out and transparent. This happens

it hard to identify. because the cloth has to share the resin

Failures happen as a result of with the wood below. To solve this prob-
temperature extremes. 70-75 degrees F. is lem, add more resin to the starved spots
ideal and 30-40% relative humidity is also while its still wet. A better solution
important. It doesn't always happen that would have been to prime the hull first.
way. Below 60 degrees any cure is going Knots and pitch pockets can cause a no-
to be slow. Above 85 and you have trouble cure situation on the surface. Again
getting it out of the pot fast enough. priming is the answer. Give an extra coat

Follow the charts for your resin! This of primer on these spots. Its better to
helps get the proper mix for the find out about this problem before you add
conditions. Mix small-batches! This the glass.
gives you a shorter time that each batch This is a very classic problem. This
is in the pot. If the resin begins to get person spent the winter building a canoe.
lumpy as you use it, give it a pitch and He moved it to the garage in early May and
mix a new batch with slightly less glassed the outside on the first warm
catalyst. day. The cure was slow but complete.

If you have completed the first coat, June came and went quickly as it always
bias strips and all, and the resin hasn't does. The inside got glassed on the 4th
begun to cure, it may be you need more of July. The rest of the boat looked
catalyst. No problem, paint on a second great but the inside turned milky.
coat that is much hotter (more catalyst). Another call to the building director,

The second coat goes much faster as you (always get them on the 5th and 6th of
are simply painting on a layer. You can July). My advice - never glass on the 4th
still get it on because you require a of July. Sound silly? Take a look at the
shorter time. humidity on the 4th and it makes sense.

If you are experiencing a really slow June and July are wet months. The actual
cure, find a way of warming up the moisture in the air is greater than during
project. A few degrees temperature change an April shower.
does wonders. If warming is impractical, I hope I have saved you a problem with
sometimes painting on a Super HOT batch this article. These are not all the
will save the day. things that can go wrong, just some of the

It is very easy to mix a test batch most common ones. Prime the hull, watch
before you start; often hard to correct the weather, try a test batch, and it will
the problem later. A small batch, about save you much grief.

on ounce, will tell you a lot about the
condition of your resin. Mix it to the
proportions on the chart and set it aside
while you do other chores.

Your test batch will cure much faster |
in the container than it would spread out |
on the hull, keep this in mind. If your

OUTDOOR TRIPS FOR
WOMEN OF ALL AGES

trekking in Nepal

test batch set in 15 minutes that is the | eenbeing: Alas, BWICA, Goshen Ozcne
pot life. The cure time may be 8-10 times | bicycling: Missouri, Wisconsin, Minnesota, Michigan
that long, depending on how thinly you | year round program
spread it and how warm the surface is. | leadership training - college credit

Failures happen because material other |
than catalyst was added to the resin or | WRITE FOR OUR CURRENT CALENDAR. |
because catalyst was added to something | 2550 Pillkbury Av. S.-.Minncapolis, M0 55404 - (612)870-8291 |

ee eS |

HUT! 11

Article contents & approved summaries (0)

No article summaries are available for this view.