← Back to The HUT

September 1984 · Vol. 20 No. 9

September 1984 Magazine (Vol. 20 No. 9)

Issue first-page cover

Magazine · 16 pages

For the full-resolution original, use Open PDF above. Your browser handles PDF zoom and navigation.

Scan page 8 of September 1984 Magazine (Vol. 20 No. 9)
Searchable text for scan page 8

BUILDER'S NOTES

- Bob Brown, Building Director in cold weather, hot weather, as well as —
‘ dry or humid weather.

The following article arrived from a _ Health concerns may be the strongest |
west coast member. His opinions are valid 2JeCctions to epoxy. The main a -
so let's here what John Campbell has to a contact dermatitis. This is a ras
say. which breaks out after a person has been

sensitized to the resin and hardeners.

"In the June, 1984 issue of HUT!, Bob The rash is not unlike poison ivy. _The
Brown has an article on things that can go Pest a it do is at Be —
wrong in fiberglass canoe building. One UST LOS ERSMee Ss welel ly UCuP en
alternate answer to the problems he resins can be removed with a good quality
describes is to use epoxy resin instead of waterless hand cleaner. At least one
polyester resin. I've not had the company does not recommend using acetone
pleasure of working with polyester resins, for fear of opening skin pores and —
but have built three woodstrip canoes allowing deeper penetration of chemicals.
using epoxy resins. My problems have been 8y themselves, the cured epoxies pose no
few which leads me to believe my original problem. However, one should take
choice of epoxy resins over polyester was adequate precautions against the dust from
correct. Before building my first canoe, sanding the resins and glass, just as one
I researched both polyester and epoxy ie Sat i at , 4
resins. While epoxy is more expensive and Modern boat builders of racing an
may pose a greater health problem, there ocean going ships are using more and more
are distinct advantages. : epoxy in hull constrution. It bonds

Tne first advantage was bonding and excellently to wood and metals and
curing with resinous wood. David Hazen produces a strong light hull. I encourage
in his book,"A Stripper's Guide to Cance everyone interested in canoe building to
Building", discusses a potential problem investigate the use of epoxy. There are a

number of mail order suppliers in the

of adhesion between polyester resins and United States and Canada. Most are

cedar and redwood hulls. Epoxy, on the

other hand, has a true affinity for wood; willing to offer technical advice over the
there are no adhesion problems with any telephone. (This means you'll probably
species. While the MCA building guide get better help than from the local store
does not discuss a potential bonding wnere the salespeople insist you really
problem, it does note a possible don't need wax to harden polyester.)
delaminating situation arising from steam _ In all, using epoxy resin will save you
created by moisture in the wood. I have time and reduce the risk of losing many
never heard of this happening with epoxy. hours of careful, loving workmanship.
Choosing epoxy over polyester appears to Since all time spent building is time away
reduce the possivility of bonding or from water, I feel the extra expense is
delamination problems. “worth the additional time I get paddling.
The second advantage is simpler mixing Also, I've been spared the embarrassment
and measuring with epoxy--a two to one of calling someone to ask why the goo
‘ratio by volume. The fewer number of wasn't getting hard.
‘steps means the lower chance of error. — .
Adding wax to cure polyester has always ; *P.S. Dear Diary...Wel1 for the first
struck me as another little detail where time the darn stuff didn’t cure right.
things can go wrong. If the wax is not Still tacky 24 hrs after application.
evenly distributed, then tacky areas occur ‘Mixed a batch of fast curing resin late on
which need additional treatment. If more | 4 Cool day. Because of short pot life,
coats of resin are needed the wax must be began to spread it on immediately. Since
removed. Epoxy doesn't require wax which this was a sealer coat on the ash
simplifies the process and removes a step gunwales, it was spread very thin. Well,
if more coats are needed. too thin, too cool, and probably didn't
Lastly, modern boat building epoxy let it develop enough body in the pot
formulations reduce the temperature and before spreading. Took it off with
humidity worries. The epoxy I currently acetone, a scraper, and some sandpaper.
use, System Three, is formulated for the Only my ego was damaged and two hours of
wide range of weather conditions found on extra work. Next coat went on fine.
the northwest coast. It works beautifully Nothing is foolproof, least of all me."

8 HUT!

Article contents & approved summaries (0)

No article summaries are available for this view.