← Back to The HUT

October 1976 · Volume/issue not printed or unknown

October 1976 Supplement

Issue first-page cover

Supplement · 40 pages

October 1976 Supplement

Captured text — scan page 7

Automatically captured text may contain recognition errors. Compare it with the original scan.

This shows the complete scan page, including any other material on it.

How to Fiberglass a Canoe Paddle by AlButton and Karl N. Ketter

Fiberglassing a canoe paddle blade increases its life. A
paddle thus processed is less likely to chip or crack, and the
protection is a must in serious whitewater paddling.

Materials required are: Paddle, sandpaper or varnish
remover, newspapers or plastic drop cloth, scraps of 4 oz.
and 6 or 7 oz. fiberglass cloth, scissors, paper cup, small
amount of epoxy resin, waxed paper, 1- to 2-inch brush, 1 to
3 pieces (bundles) of roving (18 1/2 oz.), rubber or plastic
glove, rag, and acetone cleaner.

Assemble your materials. Apply sandpaper or varnish HAY eRBSe Tle per cae
remover to the bottom 2 inches of the paddle blade. Tape the STRETCH ae Fee
paddle, blade upward, to a table leg or other similar FINGERS

structure. Protect floor and table with newspapers or
plastic. Bias cut two pieces of the 6 or 7 oz. fabric
1 1/2 inches wide by 9 to 10 inches long (1 inch longer than
paddle width—an 8-inch blade requires a 9-inch length of
fabric). Trim corners or round ends of cloth. Bias cut two
pieces of 4 oz. cloth similarly, except make them 2 inches
wide.

Wi

Mix a small amount of epoxy resin, about 1 inch in the

bottom of a paper cup. (The finish of epoxy is tougher and PUSH OUT CORNER WORK OUT ANY

harder than alternate products, and it is easier to work with Stown ey °° rican

because it’s gluey.) ieee [poke LIKE THIS

Lay a 4 oz. strip on waxed paper. Use brush to wet strip with cracking, as unreinforced resin woud do under brutal
resin. Stack on second 4 oz. strip and wet down. Add the 6 or pounding.

7 oz. strips one at a time, wetting each with resin. Stretch

Have a rag ready to wipe off drips. Use acetone to clean
each strip lengthwise as you lay it down (the bias cutting brushes a Pochod. P f

permits maximum stretchability).
For a lighter paddle, adequate for cruising and flatwater

Use a piece of roving 1 to 1 1/2 inches shorter than strips of racing, the following suggestions are offered:

fiberglass cloth. (Two or three bundles are recommended for

heavy paddle use.) Using rubber or plastic glove, dip one end Apply fiberglass cloth and resin with the paddle in a
into the resin, then the other. Lay soaked-out roving on top horizontal position to prevent the resin from running down
of cloth stack. Gently lift stack by ends and flip over the end the blade.

of the paddle lengthwise. Fan corner crease until it
disappears. Make sure roving stays on tip of paddle. Keep
working, if necessary, to remove bubbles and creases for

Use one layer of 4 oz. glass on each side of blade. Do not
attempt to bend glass over the edge, but run the glass past

half an hour or longer, until resin gets tacky. However, as inaigen OF ene DINEE:

soon as possible, turn paddle blade downward to keep resin Trim excess glass to 1/4 inch over blade size after resin has
at tip and avoid further dripping, continuing to work strip. hardened.

Note that only roving strands are used, not the roving itself. Using thickened resin, fill in the notch between the
The roving strands prevent the resin from chipping and fiberglass extensions.

INSIDE |NEXT TO PADDLE TIP

2-3 ROVING STRANOS

ORR CHE OOK KX

QO OKAY LOA AOQO9
SOO SAO OOOO
HRN) RK
Mie CRIN BOY
SOK OSC Sy
WELK KA RL LAKIN KRACK MAIO ROKK) ree
OO ESAS ESS SSS 5

“ereret

STRETCH
aie bt R 4 oz Z* x fo” —$>
OUTSIDE drawings by Larry LaPole

Page 15

Articles (10) · Summaries (10)

Generated issue overview: An October 1976 Minnesota Canoe Association HUT newsletter issue accompanied by a substantial Friends of the Boundary Waters Wilderness educational pamphlet advocating stronger wilderness protections for the Boundary Waters Canoe Area. The newsletter includes association news, canoeing and boatbuilding material, event information, racing results, and membership forms.

Generated summaries are descriptions, not original captured text. Page-range text shows complete scan pages and may include neighboring material.

THE EDITOR SAYS

Title transcribed from original publication

Generated summary: The editor comments on the delayed arrival of the September HUT, attendance at the St. Croix Color Cruise and Builder’s Contest, and the contents and upcoming activities covered in the issue. He invites members to send in photographs, comments, opinions, and articles.

Open scan page 3

Read captured page 3 →

MCA member’s input requested: Kettle River user study

Title transcribed from original publication

Generated summary: The University of Minnesota College of Forestry is studying use and user preferences on the Kettle River. The notice asks selected MCA members to complete a questionnaire and invites other interested members to request one.

Open scan page 3

Read captured page 3 →

Grand Portage Rendevous

Title transcribed from original publication

Generated summary: The article recounts the Brigade of the North’s participation in the Grand Portage Rendezvous and Indian Pow Wow. It describes the event and reports that the Brigade won the large-canoe race; John Wheeler and Tom Babcook won the two-person canoe race.

Open scan page 5

Read captured page 5 →

November Activity Meeting: Handicraft Show

Title transcribed from original publication

Generated summary: An announcement invites members and friends to a November display and contest of sporting equipment, handicrafts, inventions, art, and photography. It provides the meeting time, location, and contest guidelines.

Open scan page 6

Read captured page 6 →

How to Fiberglass a Canoe Paddle

Title transcribed from original publication

Generated summary: A practical guide to reinforcing a canoe paddle blade with fiberglass and epoxy. It lists materials and describes preparing, layering, wetting, positioning, and finishing the cloth and roving, with separate advice for a lighter-duty paddle.

Open scan page 7

Read captured pages 7–8 →

Give Your Wood Strip a Beauty Mark

Title transcribed from original publication

Generated summary: Lew Miller describes repairing a wind-damaged redwood-and-spruce strip canoe. He explains removing damaged fiberglass, replacing a damaged strip section, refinishing the hull, and reflecting humorously on the canoe’s visible repair marks.

Open scan page 10

Read captured page 10 →

Mississippi Mud: Minnesota Marathon Canoe Racing Point System

Title transcribed from original publication

Generated summary: This report explains the 1976 marathon canoe racing point system: eight sanctioned races were held, with each paddler’s best five results counted. It describes the points awarded, class participation, and the overall standings.

Open scan page 14

Read captured page 14 →

Tips on Building Whitewater Boats

Title transcribed from original publication

Generated summary: A continuation of an earlier article on building whitewater boats. The available text discusses a timed procedure for molding, trimming, clamping, and seaming a kayak, along with epoxy safety precautions and advice about commercial whitewater boats.

Open scan page 15

Read captured pages 15–18 →

You need not be a lonely canoeist

Title transcribed from original publication

Generated summary: Ketter explains how local MCA chapters can make the association’s activities and services more accessible to members outside the Twin Cities. He describes chapter formation, member participation, representation on the MCA board, and financial support for chapters.

Open scan page 19

Read captured page 19 →

Your Boundary Waters Canoe Area Wilderness needs help, NOW!

Title transcribed from original publication

Generated summary: An advocacy pamphlet presents the Boundary Waters Canoe Area as an endangered wilderness and urges stronger congressional protection. It discusses the area’s ecological and recreational value, its preservation history, logging, motor use, snowmobiles, mining, and competing Fraser and Oberstar proposals; it promotes the Fraser bill to designate the full area as wilderness.

Open scan page 21

Read captured pages 21–40 →